
|
YASKAWA MEMOCON 120 SERIES
JAMSC-120ACI02000
A/D-CUR-4CH Analog Input Module
Four-channel current and voltage analog input conversion for MEMOCON GL120 control stations.
|
Four channels for process analog signals
|
| Sales manager: Miya zheng | Email: sales@amikon.cn | WhatsApp: 86-18020776792 |
|
PRODUCT OVERVIEW
Process current acquisition for GL120
|
JAMSC-120ACI02000 converts four field analog signals into numeric values for PLC processing. Each channel accepts 4 to 20 mA current or 1 to 5 V voltage. Converted values use 12-bit binary data from 0 to 4000, and the module supports hot swapping in a compatible MEMOCON 120 station.
|
| Product family | MEMOCON GL120 / 120 Series I/O |
| Module designation | A/D-CUR-4CH |
| Input channels | 4 |
| Current input range | 4 to 20 mA |
| Voltage input range | 1 to 5 V |
| Resolution and data | 12-bit binary, 0 to 4000 |
| Overall accuracy at 25 C | +/-0.5% of full scale |
| Overall accuracy at 0 to 60 C | +/-1.0% of full scale |
| Current input impedance | 250 ohm |
| Voltage input impedance | 1 Mohm minimum |
| Internal current consumption | 450 mA |
| Maximum heating value | 2.3 W |
| Hot swapping | Permitted |
| Slots required | 1 |
| Approximate mass | 300 g |
| Dimensions | 40.3 x 130 x 103.9 mm |
| Field connection | Terminal block |
|
System fit
Install in one compatible MEMOCON 120 I/O slot and match terminal wiring to the selected current or voltage input method. Channel scaling in the CPU must correspond to 0 to 4000 data.
|
Selection value
Choose this model for four 4 to 20 mA or 1 to 5 V inputs. Do not substitute the similarly named 120AVI voltage-input variants without checking signal range and scaling.
|
Application focus
Suitable for transmitters and converted sensor signals used in pressure, flow, level, temperature and process measurement.
|
|
Twenty Years of Experience
|
Quality and Fast Response
Global automation supply, coordinated delivery and responsive quotation support for planned and urgent maintenance.
|
International Parts Network
|
| Sales manager: Miya zheng | Email: sales@amikon.cn | WhatsApp: 86-18020776792 |
| 01 | Can JAMSC-120ACI02000 accept both 4 to 20 mA and 1 to 5 V devices? | Yes, but channel wiring and signal treatment must match the chosen input method. Confirm transmitter output and loop arrangement before connection. |
| 02 | What PLC scaling is required for JAMSC-120ACI02000? | The converted range is 0 to 4000. Engineering-unit scaling must be set in the control program for each transmitter range. |
| 03 | Can JAMSC-120ACI02000 replace JAMSC-120AVI02000? | Not as a direct assumption. The ACI model is intended for 4 to 20 mA or 1 to 5 V, while AVI variants use other voltage ranges. |
| 04 | What should be checked on a used JAMSC-120ACI02000? | Inspect the terminal block, channel electronics, connector pins and label. Request channel tests with both low and high input values. |
| 05 | What details are needed to quote JAMSC-120ACI02000? | Provide the complete model, required quantity, station type, field signal range, terminal-block requirement and delivery destination. |
|
Confirm JAMSC-120ACI02000 for your system
Send the complete model, installed configuration, quantity and delivery destination.
|
|



Inventory Products


More than 40.000.000 products available and worldwide support