
|
3300 XL 8 mm PROXIMITY SYSTEM
330180-X1-CNMOD:143416-05
A modified 3300 XL 8 mm Proximitor Sensor that conditions the probe signal for non-contact shaft vibration and position measurement. The complete X1, CN and MOD markings must remain together during replacement selection.
|
![]() |
| Sales manager: Miya zheng | ✉ sales@amikon.cn | ☎ 86-18020776792 |
| 8 mm PROBE Detects shaft-to-tip gap |
➞ | EXTENSION CABLE Completes total electrical length |
➞ | 330180-X1-CN Conditions the signal |
| Product role | Modified 3300 XL 8 mm Proximitor Sensor |
| Measurement principle | Eddy-current non-contact displacement measurement |
| Linear range | 2.0 mm / 80 mil |
| Scale factor | 7.87 V/mm / 200 mV/mil nominal |
| Frequency response | 0 to 10 kHz, typical system response |
| Reference target | AISI 4140 steel for stated system performance |
| Configuration control | X1, CN and MOD:143416-05 must be checked as one complete marking |
| Configuration | What it controls | Buyer action |
| 330180-X1-CN MOD:143416-05 |
Modified total-length, mounting or regional configuration controlled by the full marking | Match every character and the MOD number; do not translate X1 into a standard code. |
| 330180-50-00 | Standard 5.0 m system length, panel mount, approvals not required | Use only when this exact standard mounting and length are required. |
| 330180-51-05 | Standard 5.0 m system length, DIN mount, multiple approvals | Use for the stated standard DIN arrangement, not as an assumed MOD substitute. |
| Sales manager: Miya zheng | ✉ sales@amikon.cn | ☎ 86-18020776792 |
| Q1 | What label evidence is required before ordering Bently Nevada 330180-X1-CN MOD:143416-05? | Capture one readable image showing 330180-X1-CN and MOD:143416-05 together, plus mounting style, terminal side and installed probe/cable markings. A quotation based only on 330180 can miss the controlled modification. |
| Q2 | How should the system length be confirmed for Bently Nevada 330180-X1-CN MOD:143416-05? | Record the probe integral-lead length and extension-cable length, then confirm their sum matches the installed Proximitor configuration. Do not infer X1 from a standard 10, 50 or 90 option. |
| Q3 | Can a standard 330180 be calibrated to replace Bently Nevada 330180-X1-CN MOD:143416-05? | Standard 3300 XL components are interchangeable within the correct system length, but a modified sensor must first be matched to its controlled mounting, regional marking and MOD requirements. Calibration does not correct a wrong hardware configuration. |
| Q4 | Which electrical readings help verify Bently Nevada 330180-X1-CN MOD:143416-05 before service? | Check supply voltage and polarity, common and output wiring, probe gap voltage, monitor input type and scale factor. An abnormal gap voltage may indicate wrong system length, damaged cabling, target geometry or an installation gap error. |
| Q5 | What arrival inspection matters most for Bently Nevada 330180-X1-CN MOD:143416-05? | Verify the complete label and MOD marking first. Then inspect the coaxial connection, terminal block, mounting base, enclosure and isolation surfaces for impact, corrosion, heat damage or unauthorized repair. |
| 1771-P6S/B | CC-TUIO41 | TP830 3BSE018114R1 | AI815 3BSE052604R1 | FU20-05-T1-NPT |
| UT55A-001-11-00 | CP471-01 | IS220PSCAH1B | 330180-51-00 | DS822.OD110 |
| PR-MAX-PRO | AMPS-24E | XP10-M | DNC-T2032-A10 | CP451-10 |
| 330101-00-63-10-02-00 | DC-TDOD61 | DC-PDIL51 | DC-TDIL61 | DC-TAOX11 |
| DC-TAIX11 | ICS Triplex T9902 | ICS Triplex T9901 | IC200CHS022L | 80026-088-01-R |
| BA21504-00-08-10-02 | 21000-28-05-00-75-01-02 | 330180-X1-05 MOD:145004-90 | 330102-00-12-90-02-05 | 330101-00-36-05-02-05 |
| 38B6041X082 | 330704-000-100-10-01-RU | 330103-00-07-10-02-05 | 086444-001 MPRC086444-001 | CI526V1 3BSE012870R1 |
| AH385851U003 | AINT-02C | 8102-HO-IP | 1771-OA | AB7000-C |
| IMASI13 | 1771-ASB/E | WDP5-118.051-00 | SOIA-01 | 6AU1425-2AD00-0AA0 |
| 1747-L542 | XC5010C | 1746-P1 | 1771-OB | 1771-OZL |
| 01 / Contact within 7 days Send order details, photographs and a clear description. |
02 / Preserve original condition Keep approved returns complete with packaging and accessories. |
03 / Inspection and resolution Return or replacement follows receipt and inspection; return shipping remains the buyer's responsibility. |
| Sales manager: Miya zheng | ✉ sales@amikon.cn | ☎ 86-18020776792 |



Inventory Products


More than 40.000.000 products available and worldwide support